košík je prázdný
košík je prázdný

TB20-C, Bus Coupler EtherNet/IP

PDFTisk
The EtherNet/IP bus coupler makes it possible to access data from peripheral modules using the EtherNet/IP protocol.
600-175-1AA11_EtherNet_IP_front

Kod produktu: 600-175-1AA11

Popis

A functioning TB20 configuration will always require a bus coupler and at least one peripheral module, but can accommodate up to 64 modules of any kind connected in series with the bus coupler. The bus coupler supports hot-plug for replacing modules during operation.
It detects peripheral modules that are plugged in and allows access to the modules` I/O data via input/output assemblies.
The EtherNet/IP bus coupler features an integrated two-port switch that allows for star and line topology configurations. 
A large I/O image table size of one kbyte makes it possible to implement comprehensive and complex systems.
TB20 ToolBox can be used to easily configure the system and the various module parameters and transfer the corresponding settings to the coupler.

Note:

The 24 V power supply connector, the final bus cover, and the base module are included as standard.
TB20 ToolBox makes it easy to methodically design TB20 systems. Integrated terminal mapping, system width calculations, and current-carrying capacity monitoring all make it possible to quickly design systems without making any mistakes. 

Characteristics

• Supports unicast and multicast CIP connections
• 511 bytes of input assembly data; 511 bytes of output assembly data
• TB20 ToolBox can be used for easy access to assembly sizes and to the structure of the image table within the 
  assemblies
• Up to 64 peripheral modules
• Modules can be replaced during operation (hot-plug)
• Implicit messaging (transport class 1)
• Explicit messaging (transport class 3)
• TCP watchdog
• IP address can be set relative to a base IP address by using a DIP switch that can be covered
• DHCP (can be selected using DIP switch)
• Integrated two-port switch with two RJ45 connectors
• Module process data is automatically assigned to the EtherNet/IP mapping
• 24 VDC power supply
• Integrated power supply unit for powering peripheral modules (2.5 A)
• Supplies the system’s I/O voltage (24 VDC)
• 9 LEDs, three of them bi-color
• USB device port for online diagnostics, configuring parameters, setup, and firmware updates with "TB20 ToolBox"
• TB20 ToolBox simulation for setting up the I/O system without a higher-level controller in order to test the system`s 
  operation (I/O check)
• Concealed "factory reset" switch for restoring the module to its factory settings

Orderdata
Product Ordernumber  
TB20-C, EtherNet/IP bus coupler,
comes with 24 V power supply connector, final bus cover, base module
600-175-1AA11

Kontakt

Česká republika
INTERSOFT - Automation s.r.o.
IČ: 49194437
Nepomucká 1355/261, 326 00 Plzeň-Černice
GPS: 49.6972006N, 13.4277131E

Anton Mózer - Elektronika, s.r.o.
Zvolenská 99, Modrý Kameň, 992 01

 

mobil: +420 602 647 033
telefon: +420 377 680 947
fax: +420 377 680 940
Po - Pá:  8:00 - 18:00
So - Ne: po domluvě
Kontaktní osoba: Michal Hlavatý
email:  
michal.hlavaty@intersoft-automation.cz
helmholz@intersoft-automation.cz
telefon:   00421 (0)47 4870 294
fax:   00421 (0)47 4870 294
e-mail:   ame@helmholz.sk
Po - Pá:   8:00 - 17:00
So - Ne:   po domluvě

Newsletter

Přihlaste se k odběru novinek.
captcha